Maybe not helpful to the current problem at hand, but I always thought a t-case brake would be cool. A little cable activated caliper on a custom bracket and a laser cut rotor on the output flange...
Type: Posts; User: Trevor?
Maybe not helpful to the current problem at hand, but I always thought a t-case brake would be cool. A little cable activated caliper on a custom bracket and a laser cut rotor on the output flange...
Just an FYI for the group: Brant (Our USFS contact) is preparing his grant request to the state OHV committee for 2022-2023. I was able to tweak James' letter from last year with my name and new...
I was up there in September. Cool place.
53849
I finally got around to getting a report and pictures out to Brant and Patrick at the USFS. When I first plotted the coordinates of that weird note I thought I had the datum wrong or some other...
I don't know how the elastic inner rope really effects it, but that looks a lot like whipping twine used to finish lines on a sailboat. It's usually a waxed polyester. A needle with a large eye can...
I wonder if once you re-tie it if you could just dip the loops in something to lock it all in. If i had to guess their dip is probably some kind of 1 or 2 part urethane. If you could get a...
Thanks everyone for coming out today. It turned out to be great weather...... we only got a little rain while airing up. Devil's Canyon wasn't too bad. A few concentrations of trash in a few of...
I can pass this along. Do you have any position information for where you found this? Maybe try to pick out the site on google maps satellite view?
Looks like we have a big turnout for tomorrow. Thanks in advance for all the interest. I just confirmed with Brant at the USFS and we should be all set.
We will be splitting into two groups once...
A little tabletop vertical bandsaw like you get with one of those Swag kits (or I get with my modified Wen:...
I have a little tabletop bandsaw from Wen that's not too bad. It's slow, but a lot quieter than chop saws and a lot cleaner than an abrasive chop saw. I also made a little table that clamps in the...
When: 10/1/2022 at 9am
Where: USFS Ranger station in Idaho Springs (I-70 and hwy 103; 101 Highway 103, Idaho Springs, CO)
Trails:Barbour Fork and Devils Canyon
Length: 4-5 hours
***
The TL:DR...
Thanks for the responses everyone. I'll go ahead and pass along our top three days to the USFS and we will get one on the books. It's unlikely I will hear back until Tuesday or Wednesday due to the...
A little info about Barbour Fork from the USFS:
"Fyi, there has been some significant ‘repairs’ to the Barbour Fork system. The Lower area near the parking lot has been fixed up to allow ...
Hello everyone. I would like to start planning our 2nd Adopt-a-Trail cleanup run for 2022. We typically target this one for one of the weekends after Labor Day so we can be sure to get any trash...
On 2 meter VHF that bonding strap may have more of an influence on the quality of the RF ground and your tune. For CB its probably more necessary. For folks working 20, 40, or 80 meters mobile the...
There's always tradeoffs, and you can always try one location and then move it later. Tub mounting can be nice because you won't have to deal wth the hinge and the need for the cable to flex every...
For the heck of it I dug around for 3/8-24 VHF/UHF antennas. It turns out I was wrong and there are a couple options out there after all.
...
For antennas I like antenna farm. https://theantennafarm.com/shop-by-categories/shop-all/mobile-antennas
They have a decent selection of pre-terminated cables as well: ...
Those firering / 3/8-24 threaded studs are not well suited for VHF and UHF frequencies. Unless you screw one through the center of a metal roof you're not going to get a good groundplane and it...
Well, we got about halfway through the run before I remembered I should snap some pictures. I am not much of a photographer.
53590
This is Cory's (KornRunner) 2nd run through this little...
Ouch. We had a rough idea something happened as we could hear you guys on GMRS from devil's canyon. Glad nobody was hurt. I like the victory photo.
I'll go ahead and get the report thread started.
Thanks again to everyone for coming out to help wit the adopt-a-trail clean up runs today. I'll have a handful of pictures up shortly, but the...
Looks like we have a good sized group going. I'll check the reservation page one last time in the morning to see if there are any last minute additions. I plan on arriving a little bit early, 8:30...