Search:

Type: Posts; User: newracer

Page 1 of 2 1 2

Search: Search took 0.06 seconds.

  1. Replies
    14
    Views
    357

    Re: Cheap Amazon LED Lights

    I connected some directly to my reverse circuit on my tow rig, no issues at all, granted I am not in reverse for long periods of time.
  2. Thread: The Campfire.

    by newracer
    Replies
    3,285
    Views
    345,914

    Re: The Campfire.

    I don't have room at my place either, luckily a good friend has room at their place.



    The main reason we decided on this is I would have likely had to upgrade my truck to a one ton to be able...
  3. Thread: The Campfire.

    by newracer
    Replies
    3,285
    Views
    345,914

    Re: The Campfire.

    A guy in a Facebook group I belong to has one that was converted to 4WD. Unfortunately mine is just 2WD.
  4. Thread: The Campfire.

    by newracer
    Replies
    3,285
    Views
    345,914

    Re: The Campfire.

    My new "tow rig."

    2007 Jayco Seneca HD 33SS

    https://i.imgur.com/soJ0xbi.jpg
  5. Thread: Ball Joints

    by newracer
    Replies
    2
    Views
    133

    Re: Ball Joints

    When I did mine, '07 JKUR, the only issue was getting the passenger side axle shaft back in. I ended up damaging the diff seal causing a leak. I then took it to a shop for the diff seal as I didn't...
  6. Replies
    14
    Views
    357

    Re: Cheap Amazon LED Lights

    They seem to be getting better and better. I bought some of the flush mount ones for backup lights on my truck, even though a few of the LEDs have gone out they are still pretty bright.

    I want a...
  7. Thread: My new rig.

    by newracer
    Replies
    35
    Views
    7,178

    Re: My new rig.

    The fuel pump was external and right behind the front seats, very noisy. Took it out, relocated filter and shut off valve, added a Holley Fuel Cell module, much better.
    ...
  8. Replies
    8
    Views
    203

    Re: strange noise in 4x4 Jeep JKU

    Did you check the front driveshaft Rzeppa joint?
  9. Replies
    31
    Views
    1,472

    Re: Front Axle U-Joints

    I am surprised the ball joint tool bent, i worked mine pretty hard using an air impact on it and its still square.

    Their torque wrenches are typically considered pretty good, not for engine...
  10. Re: 2021-02-02 (Tues) Cherokee Park - Deadfall Clearing

    Thanks for doing this!
  11. Replies
    9
    Views
    756

    Re: Trails near Leadville

    It's already on your list, I think Halfmoon Creek is a must. Only because I have never run it and I hear it is a great mixture of terrain and scenery.
  12. Replies
    29
    Views
    1,056

    Re: Cherokee park road and the area

    These are from my club's trips. The snow can be much deeper than shown in the videos.
  13. Replies
    29
    Views
    1,056

    Re: Cherokee park road and the area

    Not that I am aware of.
  14. Replies
    29
    Views
    1,056

    Re: Cherokee park road and the area

    My club goes up there snow bashing often, it can be really fun when the snow is deep. A couple of our trip planner were up there scouting this past weekend and there isn't much snow yet.

    In...
  15. Replies
    5
    Views
    363

    Re: Just a tad more than I need

    They are basically a skid loader on steroids.
  16. Replies
    163
    Views
    22,892

    Re: 58 Willys Wagon

    A cut off wheel should work fine, looks like there is plenty of room to access it. I was given a torch setup a few years ago, don't use it much but it is handy for some things.
  17. Replies
    163
    Views
    22,892

    Re: 58 Willys Wagon

    Do you have a torch?
  18. Thread: Fire damage.

    by newracer
    Replies
    4
    Views
    863

    Re: Fire damage.

    The first step will be assessing the roads to see exactly what needs to be done.
  19. Thread: Fire damage.

    by newracer
    Replies
    4
    Views
    863

    Re: Fire damage.

    It will likely be awhile before Moody opens, as the entire area burned. Only the very west end of Kelly Flats burned, I am going to push the FS to open it ASAP.
  20. Replies
    5
    Views
    369

    Re: Merry Christmas and Happy Holidays!

    Merry Christmas!!! I hope everyone had a great day!
  21. Replies
    31
    Views
    1,472

    Re: Front Axle U-Joints

    That is the kit I have. I clamped it in a vise on the workbench and used an air impact to turn it.
  22. Replies
    31
    Views
    1,472

    Re: Front Axle U-Joints

    The last time I did u-joints on my JKUR I tried the sledge and socket method and it was difficult. I then used my ball joint press and it was much easier.
  23. Replies
    3
    Views
    409

    Re: Military (USMC?) Growler

    I have never seen one before. Cool little vehicle.
  24. Re: NOW SUN DEC 13 - Bunce / Ironclads / Rock Creek???

    Looks like there were a lot of people up there today.
  25. Re: NEEDED: someone to weld/install my rock sliders!

    A member of the board.

    http://bruckerbrothersltd.com/
Results 1 to 25 of 50
Page 1 of 2 1 2
BACK TO TOP