Search:

Type: Posts; User: Hugh

Search: Search took 0.00 seconds.

  1. Poll: 2023 Anniversary Run - Little Moab/Rainbow Falls - 05.06.23

    Next Saturday (04.29.23) was the leading day for the Anniversary Run, going off poll results and the few comments on the thread. The weather isn't looking great at this point with rain/snow in the...
  2. Replies
    10
    Views
    2,434

    Poll: Re: 2023 Anniversary Run

    I see that, the Woodland Park area around Rainbow Falls isn't supposed to get a significant amount of snow throughout the week but it's looking like it's going to be wet/muddy with the approaching...
  3. Replies
    10
    Views
    2,434

    Poll: Re: 2023 Anniversary Run

    I'm about to put a planned trail run post together for the last weekend of the month. Does anyone have any input on a location?

    Or should we keep it the same with Mini Moab/Rainbow Falls trail...
  4. Replies
    12
    Views
    1,388

    Re: Central City Sunday April 2

    Sounds like we are skiing Sunday, unlikely I will make it out for a Saturday run. I have to change the engine and diff oil in my jeep as well as the engine oil on the better half's vehicle. If I...
  5. Replies
    10
    Views
    2,434

    Poll: 2023 Anniversary Run

    Lets try this again since I apparently cannot read a calendar correctly!

    500+ Views and only a few replies on the other thread so I figured I would get some more input on this before putting...
  6. Replies
    12
    Views
    1,388

    Re: Central City Sunday April 2

    Might be in, depends on which day we decide on skiing this weekend. I will try to get a decision posted by Thursday or so.
  7. Replies
    7
    Views
    1,132

    Re: March anniversary run

    I'm pretty open the next few weekends and would like to get out. Most of the trails north of 70 are pretty snowed in from what I've seen recently. I don't have much experience with anything south of...
  8. Re: Red Elephant Hill, Mill Creek, Bill Moore Lake - 10/16

    Jim, great write up on a great run. REH was definitely the most technical trail that I've done and I'm glad we could squeeze it before any more snow fell. The stripped/seized sway bar bolts will be...
  9. Re: Red Elephant Hill, Mill Creek, Bill Moore Lake - 10/16

    Shane, sounds good can't wait to see the rig with the upgrades. Always willing to give a hand if needed
  10. Re: Red Elephant Hill, Mill Creek, Bill Moore Lake - 10/16

    I'll be up there ~8:45 to get aired down and such. Replaced the rear D-turdy with a D44 a few weeks ago and have only taken it on one trip since. Added new rear UCA joints last week so it looks like...
  11. Re: Red Elephant Hill, Mill Creek, Bill Moore Lake - 10/16

    Shane, do you plan on going? Since our last run I've installed a front locker and OBA so I'm slightly better equipped than previously....minus rock sliders and skids
  12. Re: Red Elephant Hill, Mill Creek, Bill Moore Lake - 10/16

    has anyone ran this trail that can verify how necessary full skids/rock rails are? That actually may determine if I go, not trying to destroy my TJ or rip a hole in the oil pan. For reference I only...
  13. Re: Red Elephant Hill, Mill Creek, Bill Moore Lake - 10/16

    Haven't been out with the front range group in a while, count me in
  14. Replies
    27
    Views
    5,231

    Poll: Re: Choose your adventure - Memorial Day weekend

    Count me 90% in for Sunday. Side note, are you sure slaughterhouse is open? I'm seeing several sources list it as closed due to mud/erosion until 6/15 or dry conditions.
  15. Replies
    21
    Views
    5,121

    Re: New Member to the Denver Area

    Haha I found that pretty convenient that I didn't have my winch caked too. This was taken after a little wheeling at my parents house. Most of it is relatively dry except a 50 yd wide seasonal Creek/...
  16. Replies
    2
    Views
    1,535

    Re: Noisy heim joints?

    Tightness was the first thing I checked and it hasn't made a difference if I went 15 uggie duggies or just hand tight with a ratchet. Im thinking I might need to make sure the joint isn't making...
  17. Replies
    2
    Views
    1,535

    Noisy heim joints?

    Recently installed an Advance Adapters SYE, Adams DC driveshaft, and built my own adjustable rear UCA's. The UCA's were made using chromoly 3/4" heims on the axle end and chromoly/ poly joints on the...
  18. Replies
    21
    Views
    5,121

    Re: New Member to the Denver Area

    I've been keeping an eye out for a used D44 but tbh I don't see them being worth as much as they're going for now-a-days. Not a huge fan of the 8.8 under the TJ (massive pumpkin, compound angles on...
  19. Replies
    21
    Views
    5,121

    Re: New Member to the Denver Area

    Most of my michigan off-road experience has been around the Grayling area. So many old logging and military roads you can go for days with only crossing paved roads to get to the other side. Also...
  20. Replies
    21
    Views
    5,121

    Re: New Member to the Denver Area

    You are correct, only stock skid plates/no sliders for the time being. Next upgrades are sliders, oil pan skid, and super 35 kit with an ARB locker to hopefully even out the playing field with the...
  21. Replies
    21
    Views
    5,121

    Re: New Member to the Denver Area

    Thanks! It's a huge work in progress that's mainly limited by the bank account like most haha. Focusing mainly on trying to finish performance/protection upgrades before dipping into appearance too...
  22. Replies
    21
    Views
    5,121

    New Member to the Denver Area

    Hi all, just moved to the Denver area from Mid-Michigan about 2 months ago. I have a lightly modded '02 Jeep TJ that's a big work in progress. The rig has seen countless miles of logging trails,...
Results 1 to 22 of 22
BACK TO TOP