Front Range 4x4 Upcoming Trail Runs - Add a New Trail Run

Page 3 of 3 FirstFirst 123
Results 41 to 59 of 59

Thread: 58 Willys Wagon

  1. #41
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    Brian previously posted:
    "IMO, those blue Fel-Pro gaskets for the valve covers and oil pans are the shiznit, with no sealant required.

    "

    Cool - will give it a try clean and dry (fel pro website says the same thing). If it doesn't work, it will leak oil just like it has been doing and like everything else does, so no big deal. Its pretty easy to try again at the next oil change.
    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

  2. #42
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    Well finally got things back together and running again....
    While I had things apart on the bottom, I added an adpater so I can run a traditional screw on oil filter cartridge, and got the oil pan on.


    After fighting some distributor issues - the old Accel distributors a friends sent me just seem to not work anymore - I went with the traditional 60s-70's delco distributor with a Pertronix unit in it.


    Fit seems to work in the space (although the cap and rotor have to be removed to put-in or take the unit out....Hopefully with the pertronix unit it won't need much attention. ALso added a new internally resisted coil to simplify some of the wiring and firewall clutter....


    Then made it all legal...
    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

  3. The Following 2 Members Say Thanks to FINOCJ For This Post:

    Bob (December 2nd, 2019),Tom (November 13th, 2019)

  4. #43
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    ps - let me know if the photos don't work...seems like sometimes when I copy them from the ecj5 site, they don't always come across....
    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

  5. #44
    Join Date
    Mar 2012
    Member
    #1028
    Last Online
    17 Minutes Ago
    Location
    Colorado
    4x4
    '12 Jeep Wrangler Sport 2.5" lift, 33s, winch
    Posts
    3,653
    User Name
    Tom
    Real Name
    Tom
    Thanks Given
    1,257
    Thanked 692 Times in 510 Posts

    Default Re: 58 Willys Wagon



    FINOCJ previously posted:
    "ps - let me know if the photos don't work...seems like sometimes when I copy them from the ecj5 site, they don't always come across...."

    They work. That looks awesome James. Can’t wait to see it in person.
    ___________
    Tom
    -.- . ——- .— - -.-

    Life is just better in 4-Low!

    https://m.youtube.com/user/wcrosman/videos

  6. #45
    Join Date
    Sep 2011
    Member
    #921
    Last Online
    26 Minutes Ago
    Location
    Fort Collins
    4x4
    1990 Jeep Wrangler (YJ)
    Posts
    7,417
    User Name
    Jim
    Real Name
    Jim Williamson
    Thanks Given
    1,399
    Thanked 1,811 Times in 1,217 Posts

    Default Re: 58 Willys Wagon



    Congrats!

  7. #46
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    Tom previously posted:
    "They work. That looks awesome James. Can’t wait to see it in person."

    Hoping to take it up to Longmont to help Trent on Sat...will be by far its longest trip from the house....if I don't make it to Trent's, you'll know why.
    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

  8. #47
    Join Date
    Sep 2017
    Member
    #2036
    Last Online
    3 Minutes Ago
    Location
    Broomfield
    4x4
    2005 Wrangler Unlimited (LJ)
    Posts
    871
    User Name
    open_circuit
    Real Name
    Trent
    Thanks Given
    278
    Thanked 296 Times in 185 Posts

    Default Re: 58 Willys Wagon



    If you make it to Longmont, you've gone too far to find me. Looking forward to seeing the wagon!

  9. #48
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    yes...Broomfield....still the longest road trip it will have made...
    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

  10. #49
    Join Date
    Feb 2010
    Member
    #595
    Last Online
    2 Days Ago
    Location
    Evergreen, Co
    4x4
    2008 Jeep Rubicon
    Posts
    4,655
    User Name
    Jackie
    Real Name
    Jackie
    Thanks Given
    526
    Thanked 429 Times in 324 Posts

    Default Re: 58 Willys Wagon



    James - Here's another one for you!

    https://www.facebook.com/marketplace...7388609490521/
         

  11. #50
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    Dual MC set up with remote reservoir arrived today from R&P custom 4x4...Richards new R&P business (its in Oregon). Willwood MC with bracket to mount to frame for oem floor pedal set-up. Has remote reservoir that mounts on inner fender so it easy to check and fill fluid. Unlike the CJ the wagon doesn't have the inspection cover in the floor (and the sbc exhaust may also make access to the MC more difficult than the L6?), so this should make it easier to deal with. This MC works nicely with R&Ps disc set up with proper RPV - future project maybe, but for now I am keeping oem drums. Will hopefully start on this later this week...have DD maintenance tonight and skiing this weekend so....keep you posted.
    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

  12. #51
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    Old MC out without damaging or mangling anything....probably will have some brake line bending and new fittings etc to make....and will have to figure out a brake light switch.


    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

  13. The Following Member Says Thanks to FINOCJ For This Post:

    Tom (January 17th, 2020)

  14. #52
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    slow progress...mocked up the new mounting bracket from R&P - it uses the same 2 frame mounts the OEM MC uses the support mount on the pedal pivot - then fit the cylinder....now need to mock up the remote reservoirs which I intend to mount on the inner driver side fender?

    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

  15. #53
    Join Date
    Sep 2018
    Member
    #2215
    Last Online
    1 Day Ago
    Location
    Castle Rock Colorado
    4x4
    06 Jeep LJ
    Posts
    97
    User Name
    Rocrawlr
    Real Name
    Gerald
    Thanks Given
    55
    Thanked 54 Times in 25 Posts

    Default Re: 58 Willys Wagon



    That's a good looking MC bracket, nicely done!

  16. #54
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    This brake project is the project that just doesn't make much progress....
    After fitting up the MC install, it was time to work on the brake lines and figure out a brake light switch. I was thinking (hoping?) this was going to be pretty simple with just reshaping some of the ends of the brake lines by the MC, but it turns out the OEM brake line set-up was a bit surprising. There are 2 lines (different size) that come out of the junction block with the brake light switch. The small 3/16 line only goes to the front driver side. The larger 1/4 line goes around the front frame member and into a junction block by the front passenger side. One out line goes to the front passenger brake, and the other out line continues down the passenger frame rail and into another junction block at the rear axle - splitting to each rear brake. This is oem according to the FSM:


    Here is the junction block at the passenger front - the 1/4 line from the MC comes in on the left. The right out is 3/16 to the passenger front wheel cylinder, and the bottom out is 3/16 and goes to the rear brakes.


    As I want the new MC for the dual res/circuit aspect, I need the both front brakes plumbed together, and both rear brakes plumbed together. So new brakes lines it is....I am making a 3/16 line that will go from one MC res around the front (following the oem routing), but it will connect directly and only to the rear brake. Here is my initial attempt to bend it up:


    I think it came out pretty welll - just one goofy spot on the front passenger. I used a small handheld bender and zip tied as I went along to hold it to the old line to help make sure all my bends matched the original and stayed 'on-plane'. I left some room on the MC end so I can figure out that fitting when more in place. The hard part will be getting it back in place and test fitting - may have to remove the radiator (argghhh). I don't want to flare the ends until I have it just right, but I might have to flare the MC end with the line in place...

    The front circuit will be a bit more difficult - have to put a junction block (with light switch) soon after the MC, and then route the passenger line around the front as well....
    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

  17. #55
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    Some progress...I almost feel like I made rough drafts of the brake lines, and now I should completely do them again without all the little errors....

    The MC - the circuit coming from the back of the MC goes to the front brake distribution block I mounted in the frame channel. The top output goes the the front driver side drum. The other output that is empty will go around to the front passenger drum. The brake light switch will go in just above the mounting bolt. The circuit coming from the front of the MC follows the OEM routing along the front frame rail....

    It then connects to the remainder of the rear brake line. The open connection is for the front passenger brake...
    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

  18. #56
    Join Date
    Mar 2008
    Member
    #1
    Last Online
    9 Hours Ago
    Location
    Naples, FL
    Age
    69
    4x4
    4Runner - Sold
    Posts
    14,272
    User Name
    Chris
    Real Name
    Chris
    Thanks Given
    575
    Thanked 796 Times in 588 Posts

    Default Re: 58 Willys Wagon



    Wow, nice find I just read for the first time. Great thread making me miss CO even more.
    ___________
    Chris in Florida

  19. The Following Member Says Thanks to Chris For This Post:

    FINOCJ (1 Week Ago)

  20. #57
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    Should have some down time to continue to work on it over the next month....Been focus the last 1.5 weeks on basement work, and that will continue for a while longer. The garage is only so big, and its sort of set-up for the cutting the flooring and baseboards etc. Then painting the baseboards and once that is all done, its back to brake lines, and modifying a fan shroud in some way to help with cooling.
    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

  21. #58
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    Brake lines finished...really hope the flare fittings seal.
    New distribution block for the front circuit. Light switch will go into block as well.
    Reservoirs mounted
    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

  22. #59
    Join Date
    Jul 2014
    Member
    #1546
    Last Online
    14 Minutes Ago
    Location
    Denver, CO
    Age
    41
    4x4
    1970CJ5-1958WillysWagon-2010Tacoma
    Posts
    2,387
    User Name
    FINOCJ
    Real Name
    James Orofino
    Thanks Given
    702
    Thanked 883 Times in 547 Posts

    Default Re: 58 Willys Wagon



    Radiator shroud....Looking back in this thread you can see I replaced the radiator it came with which was not original (was seeping and did not fit very well)...There was a big gap between the radiator and fan, so I put a spacer behind the fan moving it forward, and also used some spacers to move the radiator back...

    With the sbc swap, the fan sits pretty low and off to to the passenger side which doesn't help with cooling. Although it stays plenty cool when moving along, it wasn't quite enough to keep it cool when sitting in stop and go (mostly stop) traffic around here...So a fan shroud is needed and with the radiator out for the brake line work, now is a good time to do it...
    Here was the homebrew shroud it came with from PO - which is now long gone...


    I used a universal shroud kit with the push-through pins, did some slight modifications to the shroud and got it mounted on the radiator...With the sbc swap, the fan is low and quite off-center to the passenger side of the radiator...


    After doing it, here are my thoughts: I don't mind the push-pin part so much, and the light shroud is solidly held in place...but the plastic threads and washers leave a lot to be desired. It doesn't take much to destroy/strip the plastic threads and wonder how long they will hold the shroud in place. Thinking of replacing the plastic push-pin with some small machine screws or like 1/4" bolts and better washers to go with the rubber washers and wing nuts - or maybe just use some nylock nuts in place of the wing nuts. Now that the plastic push pin has safely made the the 'hole' through the fins, it would be simple to replace with something a bit stronger. Of course, new bolts requires a trip to the hardware store....not my favorite activity right now...
    Its not perfect, but I think its pretty good and hopefully it won't take much to keep it cool....


    With the radiator moved to the proper forward position, the blade sits about right in terms of depth - the edge is right about half the blade. Plus there is no gap between the radiator and front grill which should funnel more fresh air over through the radiator helping cooling:


    And I probably have a bit too much gap around the outside circumference - its probably 1.5-2" instead of 1" but still seems pretty good:


    Moving the radiator forward to its proper mounting position has some benefits:
    1) keeps fresh air coming through the grill also going through the radiator...with the 1" spacers, some fresh air coming through the grill could then bypass the radiator going through the gap between the grill and radiator. It also means fresh air from outside the grill is pulled through the radiator at slow speed, as opposed to pulling hotter air from the engine bay around and through the grill.
    2) The Champion radiator fits perfect in terms of the mounting holes on the grill, but it leaves absolutely no clearance in terms of height between the front cross-member under the radiator, and the top of the radiator cap on the underside of the hood...The underside of the hood was sitting/rubbing the top of the radiator cap as it was, and the hood did not quite close the way you'd want it to. With the radiator just a bit further forward, there is just a smidge more room, and it feels like the hood closes properly, but it may still rub a bit.

    Downside to moving the radiator forward...the fan is now farther away but hopefully the shroud will more than compensate and help it pull more air through the radiator. Also, the outlet hose on the radiator may be blocked by the battery tray support...This is gonna be close whether it will fit or not...but if not, I'll cut it out and weld it in differently...
    ___________
    James Orofino
    1970 CJ5
    1958 Willys Wagon
    2010 Tacoma TRD

Page 3 of 3 FirstFirst 123

Similar Threads

  1. BIG WILLYS
    By Spieg in forum Cool Finds
    Replies: 3
    Last Post: June 29th, 2019, 09:23 PM
  2. 1960 Willys Wagon
    By FINOCJ in forum Cool Finds
    Replies: 9
    Last Post: June 10th, 2019, 12:10 PM
  3. 55 Willys Wagon
    By FINOCJ in forum Cool Finds
    Replies: 1
    Last Post: May 9th, 2018, 06:43 PM
  4. Willys FC Project
    By Getaklu in forum Cool Finds
    Replies: 1
    Last Post: February 13th, 2018, 04:09 PM
  5. 1962 Willys Wagon with a twist
    By Goofy in forum Cool Finds
    Replies: 5
    Last Post: December 30th, 2015, 11:40 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
BACK TO TOP