Front Range 4x4 Upcoming Trail Runs - Add a New Trail Run

Results 1 to 15 of 15

Thread: K5 cage progress

  1. #1
    Join Date
    Jun 2015
    Member
    #1731
    Last Online
    August 17th, 2018
    Location
    Larkspur
    Age
    48
    4x4
    1988 K5 Blazer
    Posts
    57
    User Name
    wuan2000
    Real Name
    Greg
    Thanks Given
    29
    Thanked 14 Times in 10 Posts

    Default K5 cage progress



    Finally getting back to the K5 project. I've been out of the mix for a while with various 'to-do' items. The cage is underway and finally snagged the 14 bolt FF and Dana 60 front for the swap project. Good lord, the asking prices for these axles has matched the trends of the Colorado real estate market!

    Additionally, I've added some new tools in the shop to make life easier (sort of) for fabrication. The Bend-Tech software has been a godsend. Its made the process far more efficient by mitigating some of the waste and second guessing a few notches and bends. The new tube notcher and the air/hydraulic ram on the bender has saved on some extra grunts and beads of sweat as well.

    I'm hoping to have the axles swapped, the 4-link fab'd up, and the PSC steering gear in place by early May. I'd love to haul it to Moab in May for a run. Fingers crossed my plans come to fruition...and my wallet doesn't get lost.
                

  2. #2
    Join Date
    May 2011
    Member
    #834
    Last Online
    April 21st, 2021
    Location
    Colorado Springs
    4x4
    2004 Jeep LJ
    Posts
    1,107
    User Name
    Brian
    Real Name
    Brian
    Thanks Given
    670
    Thanked 354 Times in 249 Posts

    Default Re: K5 cage progress



    Looking good!

  3. The Following Member Says Thanks to Brian For This Post:

    wuan2000 (March 4th, 2017)

  4. #3
    Join Date
    May 2013
    Member
    #1222
    Last Online
    July 26th, 2020
    Location
    fort collins co
    Age
    43
    4x4
    sami buggy
    Posts
    713
    User Name
    redneck23ms
    Real Name
    alex
    Thanks Given
    0
    Thanked 86 Times in 78 Posts

    Default Re: K5 cage progress



    just doing the bed cage or are you going to continue it into the cab?

  5. The Following Member Says Thanks to redneck23ms For This Post:

    wuan2000 (March 4th, 2017)

  6. #4
    Join Date
    Mar 2016
    Member
    #1841
    Last Online
    June 16th, 2021
    Location
    SW Denver
    4x4
    Poison Spyder buggy, 1999 4runner
    Posts
    813
    User Name
    TJS86TOY
    Real Name
    TJ
    Thanks Given
    169
    Thanked 212 Times in 136 Posts

    Default Re: K5 cage progress



    Little jealous of the hydro on the bender Cage is Looking most excelenteee !!

  7. The Following Member Says Thanks to TJS86TOY For This Post:

    wuan2000 (March 4th, 2017)

  8. #5
    Join Date
    Jun 2011
    Member
    #853
    Last Online
    December 23rd, 2023
    Location
    Highlands
    4x4
    2006 Jeep LJ
    Posts
    7,483
    User Name
    Java
    Real Name
    Paul
    Thanks Given
    2,070
    Thanked 1,788 Times in 1,261 Posts

    Default Re: K5 cage progress



    Really nice work!

  9. The Following Member Says Thanks to Java For This Post:

    wuan2000 (March 4th, 2017)

  10. #6
    Join Date
    Jun 2015
    Member
    #1731
    Last Online
    August 17th, 2018
    Location
    Larkspur
    Age
    48
    4x4
    1988 K5 Blazer
    Posts
    57
    User Name
    wuan2000
    Real Name
    Greg
    Thanks Given
    29
    Thanked 14 Times in 10 Posts

    Default Re: K5 cage progress



    redneck23ms previously posted:
    "just doing the bed cage or are you going to continue it into the cab?"

    good question, glad you asked! Yes, continuing into the cab; around doors, roof and across the dash.

  11. #7
    Join Date
    Jun 2015
    Member
    #1731
    Last Online
    August 17th, 2018
    Location
    Larkspur
    Age
    48
    4x4
    1988 K5 Blazer
    Posts
    57
    User Name
    wuan2000
    Real Name
    Greg
    Thanks Given
    29
    Thanked 14 Times in 10 Posts

    Default Re: K5 cage progress



    Thanks TJ!

  12. #8
    Join Date
    Dec 2012
    Member
    #1118
    Last Online
    4 Hours Ago
    Location
    Aurora
    Age
    68
    4x4
    03 Ranger FX4
    Posts
    6,018
    User Name
    The StRanger
    Real Name
    Sam
    Thanks Given
    125
    Thanked 551 Times in 484 Posts

    Default Re: K5 cage progress



    Very nice work....
    ___________
    In a never ending search for the proper mix of dirt & rock !

  13. The Following Member Says Thanks to The StRanger For This Post:

    wuan2000 (March 4th, 2017)

  14. #9
    Join Date
    Mar 2014
    Member
    #1408
    Last Online
    September 7th, 2017
    Location
    Frederick Colorado
    4x4
    1975 Bronco Denver Edition
    Posts
    446
    User Name
    EKXJ87
    Real Name
    Steve
    Thanks Given
    96
    Thanked 69 Times in 62 Posts

    Default Re: K5 cage progress



    Very nice work on the cage! Which Bend-tech software did you end up getting? so will the programming also tell you the angle of the notches.

  15. The Following Member Says Thanks to EKXJ87 For This Post:

    wuan2000 (March 15th, 2017)

  16. #10
    Join Date
    Jun 2015
    Member
    #1731
    Last Online
    August 17th, 2018
    Location
    Larkspur
    Age
    48
    4x4
    1988 K5 Blazer
    Posts
    57
    User Name
    wuan2000
    Real Name
    Greg
    Thanks Given
    29
    Thanked 14 Times in 10 Posts

    Default Re: K5 cage progress



    EKXJ87 previously posted:
    "Very nice work on the cage! Which Bend-tech software did you end up getting? so will the programming also tell you the angle of the notches."

    Thanks Steve. I have the Bend-Tech Pro 7.x with the Armor Pack and Steel Plate add-ons. And yes, there is a notching function in the program that assists with cut-outs/notches. Prior to this, I used the PipeMaster contour gauge...which worked fine. But the notching tool in the program allows for printing out the wrapper(s) to transfer to the tubing for darn-near perfect notches every time. The software has paid for itself many times over in just reducing/eliminating material waste (cost). I'll post some updates as I progress into the cab. Right now, I'm working on the 4-link and axles. I had to pretty much rebuild the Dana 60 I picked up. Waiting on a few things to arrive on the porch. Thanks again!

    Onward!

  17. #11
    Join Date
    Mar 2014
    Member
    #1408
    Last Online
    September 7th, 2017
    Location
    Frederick Colorado
    4x4
    1975 Bronco Denver Edition
    Posts
    446
    User Name
    EKXJ87
    Real Name
    Steve
    Thanks Given
    96
    Thanked 69 Times in 62 Posts

    Default Re: K5 cage progress



    Very Cool Program I may have to consider it for my upcoming project. Thank for sharing !

  18. #12
    Join Date
    Jun 2015
    Member
    #1731
    Last Online
    August 17th, 2018
    Location
    Larkspur
    Age
    48
    4x4
    1988 K5 Blazer
    Posts
    57
    User Name
    wuan2000
    Real Name
    Greg
    Thanks Given
    29
    Thanked 14 Times in 10 Posts

    Default Re: K5 cage progress



    In the K5; ready to progress into the cab and frame points. The darn Dana 60 rebuild has added delays, but as many of you know, well worth it.
    I've designed the rear tube bumper that I'll start on after the 4-link project is done. Ugh...there's just not enough time in the day with a regular work schedule. Can't wait to win the lotto!
          

  19. #13
    Join Date
    Jun 2015
    Member
    #1731
    Last Online
    August 17th, 2018
    Location
    Larkspur
    Age
    48
    4x4
    1988 K5 Blazer
    Posts
    57
    User Name
    wuan2000
    Real Name
    Greg
    Thanks Given
    29
    Thanked 14 Times in 10 Posts

    Default Re: K5 cage progress



    Okay...(sigh)...it’s been a while. A lot has been going on that has pretty much stifled the K5 project. BUT, I’m ready to get back on track. Since last fall, I’ve acquired quite a bit of equipment and it’s been busy since. Here’s the K5 project as of today (4/14):
    14 bolt rear, trussed, pinion guard, w/locker - done
    D60 front with locker - 90% done
    4-link front/back - 50% done
    PSC hydro steer kit - ordered 4/12
    ORI Struts - got ‘em (November ‘17)
    Shock/Strut hoops & towers - umm...haven’t started those yet.
    Beadlocks - making them on the CNC at any time.
    Fuel cell - need to order
    Brake lines and drive shafts - need to route and order. (Ugh!)

    I now have pretty much an adequate fab shop. 4x8 CNC plasma table, HUGE powder coat oven and spray booth, air/hydro tube bender, 20 ton press with finger break, welders, 9k lift...and so on. But the CNC business has kept me busy on everything but my own rig. 😞 I really need to get this K5 crawler finished!! I’m sooo missing the trails.

  20. #14
    Join Date
    Jun 2015
    Member
    #1731
    Last Online
    August 17th, 2018
    Location
    Larkspur
    Age
    48
    4x4
    1988 K5 Blazer
    Posts
    57
    User Name
    wuan2000
    Real Name
    Greg
    Thanks Given
    29
    Thanked 14 Times in 10 Posts

    Default Re: K5 cage progress



    No, the bead locks won’t be bright green...that was just a powder coat color for demonstration. 😉
            

  21. #15
    Join Date
    Mar 2016
    Member
    #1841
    Last Online
    June 16th, 2021
    Location
    SW Denver
    4x4
    Poison Spyder buggy, 1999 4runner
    Posts
    813
    User Name
    TJS86TOY
    Real Name
    TJ
    Thanks Given
    169
    Thanked 212 Times in 136 Posts

    Default Re: K5 cage progress



    Good clean work! What length ORI's did you get? Are you going for aluminum lower links?

Similar Threads

  1. Need a little more help w/ my cage.
    By ajordan1975 in forum Member Skills
    Replies: 7
    Last Post: April 12th, 2015, 05:31 PM
  2. OR-Fab Weld-In Sport Cage for a CJ
    By jpmutschler in forum For Sale, Wanted, Trade, Free
    Replies: 2
    Last Post: March 24th, 2015, 08:53 PM
  3. Hell of a roll cage!
    By Jim in forum Chat
    Replies: 5
    Last Post: November 24th, 2013, 06:09 PM
  4. My Exo Cage
    By mattzj98 in forum Build Threads
    Replies: 16
    Last Post: February 1st, 2012, 09:13 AM
  5. ultimate exo cage
    By Roostercruiser in forum Chat
    Replies: 3
    Last Post: March 21st, 2011, 10:15 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
BACK TO TOP