-
8 Attachment(s)
K5 cage progress
Finally getting back to the K5 project. I've been out of the mix for a while with various 'to-do' items. The cage is underway and finally snagged the 14 bolt FF and Dana 60 front for the swap project. Good lord, the asking prices for these axles has matched the trends of the Colorado real estate market! :frown:
Additionally, I've added some new tools in the shop to make life easier (sort of) for fabrication. The Bend-Tech software has been a godsend. Its made the process far more efficient by mitigating some of the waste and second guessing a few notches and bends. The new tube notcher and the air/hydraulic ram on the bender has saved on some extra grunts and beads of sweat as well.
I'm hoping to have the axles swapped, the 4-link fab'd up, and the PSC steering gear in place by early May. I'd love to haul it to Moab in May for a run. Fingers crossed my plans come to fruition...and my wallet doesn't get lost. :D
-
Re: K5 cage progress
-
Re: K5 cage progress
just doing the bed cage or are you going to continue it into the cab?
-
Re: K5 cage progress
Little jealous of the hydro on the bender :thumb: Cage is Looking most excelenteee !!
-
Re: K5 cage progress
Really nice work! :thumb:
-
Re: K5 cage progress
[QUOTE=redneck23ms;311339]just doing the bed cage or are you going to continue it into the cab?[/QUOTE]
good question, glad you asked! Yes, continuing into the cab; around doors, roof and across the dash.
-
Re: K5 cage progress
-
Re: K5 cage progress
-
Re: K5 cage progress
Very nice work on the cage! Which Bend-tech software did you end up getting? so will the programming also tell you the angle of the notches.
-
Re: K5 cage progress
[QUOTE=EKXJ87;311405]Very nice work on the cage! Which Bend-tech software did you end up getting? so will the programming also tell you the angle of the notches.[/QUOTE]
Thanks Steve. I have the Bend-Tech Pro 7.x with the Armor Pack and Steel Plate add-ons. And yes, there is a notching function in the program that assists with cut-outs/notches. Prior to this, I used the PipeMaster contour gauge...which worked fine. But the notching tool in the program allows for printing out the wrapper(s) to transfer to the tubing for darn-near perfect notches every time. The software has paid for itself many times over in just reducing/eliminating material waste (cost). I'll post some updates as I progress into the cab. Right now, I'm working on the 4-link and axles. I had to pretty much rebuild the Dana 60 I picked up. :erm: Waiting on a few things to arrive on the porch. Thanks again!
Onward!
-
Re: K5 cage progress
Very Cool Program I may have to consider it for my upcoming project. Thank for sharing !
-
2 Attachment(s)
Re: K5 cage progress
In the K5; ready to progress into the cab and frame points. The darn Dana 60 rebuild has added delays, but as many of you know, well worth it.
I've designed the rear tube bumper that I'll start on after the 4-link project is done. Ugh...there's just not enough time in the day with a regular work schedule. Can't wait to win the lotto! :D
-
Re: K5 cage progress
Okay...(sigh)...it’s been a while. A lot has been going on that has pretty much stifled the K5 project. BUT, I’m ready to get back on track. Since last fall, I’ve acquired quite a bit of equipment and it’s been busy since. Here’s the K5 project as of today (4/14):
14 bolt rear, trussed, pinion guard, w/locker - done
D60 front with locker - 90% done
4-link front/back - 50% done
PSC hydro steer kit - ordered 4/12
ORI Struts - got ‘em (November ‘17)
Shock/Strut hoops & towers - umm...haven’t started those yet.
Beadlocks - making them on the CNC at any time.
Fuel cell - need to order
Brake lines and drive shafts - need to route and order. (Ugh!)
I now have pretty much an adequate fab shop. 4x8 CNC plasma table, HUGE powder coat oven and spray booth, air/hydro tube bender, 20 ton press with finger break, welders, 9k lift...and so on. But the CNC business has kept me busy on everything but my own rig. 😞 I really need to get this K5 crawler finished!! I’m sooo missing the trails.
-
4 Attachment(s)
Re: K5 cage progress
No, the bead locks won’t be bright green...that was just a powder coat color for demonstration. 😉
-
Re: K5 cage progress
Good clean work! What length ORI's did you get? Are you going for aluminum lower links?